焊后热处理对聚变堆用奥氏体不锈钢MAG焊焊缝金属冲击韧性的影响

doi:10.16568/j.0254-6086.202001010

核聚变与等离子体物理 ›› 2020, Vol. 40 ›› Issue (1): 59-64.DOI: 10.16568/j.0254-6086.202001010

焊后热处理对聚变堆用奥氏体不锈钢MAG焊焊缝金属冲击韧性的影响

孙振超，李鹏远*，张腾，陈辉，许丹，邓华林，康道安，罗蓉蓉

(核工业西南物理研究院，成都 610041)

收稿日期:2018-11-01 修回日期:2019-07-08 出版日期:2020-04-15 发布日期:2020-04-20
作者简介:孙振超(1984-)，男，山东烟台人，硕士，副研究员，主要从事聚变堆材料与工艺方面研究。
基金资助:
国家磁约束核聚变能发展研究专项(2008GB107001；2008GB107001)

Effect of post-weld heat treatment on impact toughness of MAG weld metal of austenitic stainless steel for fusion reactor

SUN Zhen-chao, LI Peng-yuan, ZHANG Teng, CHEN Hui, XU Dan, DENG Hua-lin, KANG Dao-an, LUO Rong-rong

(Southwestern Institute of Physics, Chengdu 610041)

Received:2018-11-01 Revised:2019-07-08 Online:2020-04-15 Published:2020-04-20

摘要/Abstract

摘要：

对聚变堆用316LN奥氏体不锈钢熔化极活性气体保护电弧焊(MAG焊)接接头进行不同温度的热处理，并在液氮温度下进行夏比冲击试验。利用光学显微镜、扫描电镜、EDS分析等研究了热处理温度对接头微观组织、断口形貌及析出物的影响。结果表明，873K热处理可以显著提高焊缝金属冲击韧性，但随着热处理温度的上升，焊缝金属逐渐出现沿着晶界分布的析出物，韧性逐渐下降。断口均为延性断裂，但随着热处理温度的升高，韧窝变浅、数量变少。韧窝底部存在球状析出和不规则状析出，球状析出在焊接过程中产生，不因热处理温度而变化，不规则析出随着热处理温度的升高逐渐增多。焊材中的Mo含量过高导致焊缝金属中Mo在晶界大量偏聚，促进了σ相的析出，当σ相在晶界形成连续分布后，焊缝金属冲击韧性显著下降。

关键词: 熔化极活性气体保护电弧焊；316LN；热处理；冲击韧性；&sigma, 相

Abstract:

After heat treatment of metal active gas arc welding (MAG weld) joints of 316LN austenitic stainless steel for fusion reactor at different temperatures, Charpy impact test at liquid nitrogen temperature was carried out. The effects of heat treatment temperature on microstructure, fracture morphology and precipitates were studied with optical microscope, SEM and EDS analysis. Results indicated that the impact toughness of weld metal could be significantly improved by 873K heat treatment. However, with the rising of heat treatment temperature, the precipitates were generated gradually along the grain boundary and a gradual decrease of toughness occurred as well. All fracture was ductile. The dimple became shallow and less with the increase of temperature. Spherical and irregular precipitates were found at the bottom of the dimple. The spherical precipitates generated during welding were free from the influence of the heat treatment, and the irregular precipitates increased with the rising of temperature. High content of Mo in filler materials led to a great segregation of Mo at the grain boundary, which would promote the precipitation of σ phase. Impact toughness of weld metal decreased significantly when continuous distribution of σ phase formed at grain boundary.

Key words: MAG welding, 316LN, Heat treatment, Impact toughness; &sigma, phase

中图分类号:

TG407

孙振超，李鹏远*，张腾，陈辉，许丹，邓华林，康道安，罗蓉蓉. 焊后热处理对聚变堆用奥氏体不锈钢MAG焊焊缝金属冲击韧性的影响[J]. 核聚变与等离子体物理, 2020, 40(1): 59-64.

SUN Zhen-chao, LI Peng-yuan, ZHANG Teng, CHEN Hui, XU Dan, DENG Hua-lin, KANG Dao-an, LUO Rong-rong. Effect of post-weld heat treatment on impact toughness of MAG weld metal of austenitic stainless steel for fusion reactor[J]. NUCLEAR FUSION AND PLASMA PHYSICS, 2020, 40(1): 59-64.

参考文献

[1] Mitchell N, Devred A, Libeyre P, et al. The ITER magnets: design and construction status[J]. IEEE Transactions on Applied Superconductivity, 2012, 22(3): 4200809-4200809.

[2] 沈旭, 孙宇峰, 吴杰锋, 等. 焊后热处理对316LN焊接残余应力的影响[J]. 热加工工艺, 2015, 44(5): 191-193.

[3] 刘丽平, 叶民友, 吴杰锋, 等. 焊后热处理对核聚变用316LN焊接接头的影响[J]. 核聚变与等离子体物理, 2017, 37(3): 342-345.

[4] Abhay Kumar, Soni R K, Ganesh P, et al. A study on low magnetic permeability gas tungsten arc weldment of AISI 316LN stainless steel for application in electron accelerator[J]. Materials and Design, 2014, 53: 86-92.

[5] Aviles S I, Boyer C, Fernandez P P, et al. A comparative study of fracture toughness at cryogenic temperature of austenitic stainless steel welds[J]. J. Mater. Eng. Perfor., 2018, 27(4): 1995-2002.

[6] Lippold J C, Kotechi D J. 不锈钢焊接冶金学及焊接性[M]. 北京: 机械工业出版社, 2008.

[7] Perricone M J, Anderson T D, Robion C V, et al. Effect of composition on the formation of sigma during single-pass welding of mo-bearing stainless steels [J]. Metallurgical & Materials Transactions A, 2007, 38(9): 1976-1990.

[8] Chun E J, Baba H, Terashima K, et al. Prediction of σ phase precipitation in type 316FR stainless steel weld metal [J]. Quarterly Journal of the Japan Welding Society, 2013, 31(4): 168-172.

[9] 张寿禄, 赵泳仙, 宋丽强, 等. 超级双相不锈钢00Cr25Ni7Mo4N中χ相时效析出的研究[J]. 钢铁, 2012, 47(2): 72-75.

[10] Folkhard E. 不锈钢焊接冶金 [M]. 北京: 化学工业出版社, 2004.

[11] 倪冰, 刘浏, 姚同路, 等. 钢中铝-硅-锰复合脱氧反应的热力学计算[J]. 钢铁研究学报, 2011, 23(9): 8-11.

[12] Kane S F, Farland A L, Siewert T A, et al. Welding consumable development for a cryogenic (4K) application[J]. Welding Journal, 1999, 78(8): 89-96.

[1]	王超, 黄梅, 陈罡宇, 陈程. 氮化硼陶瓷105GHz/1MW微波透射窗的研究[J]. 核工业西南物理研究院, 2025, 45(1): 34-38.
[2]	赵平安, 丁芳, 张青, 余林, 孟令义, 胡振华, 王亮, 余耀伟, 丁锐, 罗广南. EAST上外偏滤器靶板粒子流分布与中性气体压强关系的实验研究[J]. 核工业西南物理研究院, 2025, 45(1): 84-90.
[3]	袁金榜, 袁博达, 许敏, 余羿, 聂林, HL-A 实验团队 . HL-2A 托卡马克上 blob 结构的喷气成像观测和定量研究[J]. 核工业西南物理研究院, 2024, 44(4): 464-469.
[4]	朱有敬, 程钧, 严龙文, 王威策, 黄治辉, 吴娜, 许宇鸿, 石中兵, 季小全, 钟武律, 许敏 . HL-2A 装置上刮削层丝状结构时空特征的实验研究[J]. 核工业西南物理研究院, 2024, 44(3): 334-342.
[5]	文若楠, 姚可, 刘仪, 许宇鸿, 石中兵, 钟武律. HL-2A装置二氧化碳激光相干散射系统的研制[J]. 核工业西南物理研究院, 2024, 44(2): 125-132.
[6]	龚少博, 余羿, 王志斌, 王华杰, 袁金榜, 刘灏, 吴婷, 龙婷, 陈逸航, 柯锐, 聂林, 王占辉, 孙爱萍, 许敏. HL-2A装置相衬成像系统的安全连锁与远程监控[J]. 核工业西南物理研究院, 2024, 44(2): 157-162.
[7]	黄海宏, 陶宏亮, 王海欣 . ITER稳态磁场测试装置磁体电源设计与控制研究[J]. 核工业西南物理研究院, 2023, 43(3): 249-254.
[8]	王荣良, 刘永, 赵海林, 周天富, 提昂, 凌必利, 朱则英 . EAST等离子体电子温度涨落特征的初步实验研究[J]. 核工业西南物理研究院, 2023, 43(3): 340-346.
[9]	曾浩, 冯鲲, 刘丽娟, 白兴宇, 王超, 陈娅莉, 梁军, 卢波. LHCD 系统微波激励源性能优化设计[J]. 核聚变与等离子体物理, 2023, 43(1): 68-74.
[10]	王雍钦, 郝广周, 虞立敏, 苗雨田, 柯锐, 邹云鹏, 高庆弟 . 环位形下鱼骨模驱动快离子输运的数值模拟研究[J]. 核聚变与等离子体物理, 2022, 42(4): 440-447.
[11]	周润晖, 曹宏睿, 赵金龙, 刘士兴, 张伟, 李强, 陈开云, 俞红, 胡立群. 基于激光二极管的软X射线相机信号的自检设计[J]. 核聚变与等离子体物理, 2022, 42(2): 229-235.
[12]	赵炳炎, 陈宗华. 二维双流不稳定性静电粒子模拟[J]. 核聚变与等离子体物理, 2022, 42(2): 257-263.
[13]	彭建飞, 廖超, 宣伟民, 王海兵, 李华俊, 卜明南, 徐丽荣, 胡浩天, 石迎天 . HL-2M 装置 300MVA 脉冲发电机组电气制动系统研究 [J]. 核聚变与等离子体物理, 2022, 42(1): 8-13.
[14]	彭建飞, 宣伟民, 将宝钢, 魏玉国, 李华俊, 王海兵, 王英翘 . HL-2M 装置 300MVA 脉冲发电机组的设计[J]. 核聚变与等离子体物理, 2021, 41(s2): 443-448.
[15]	李维斌, 陈宇红, 王雅丽, 郑雪, 任青华, 吴一, 韩艾玻, 王英翘, 宣伟民 . 磁场电源在 HL-2M 装置初始等离子体放电中的应用[J]. 核聚变与等离子体物理, 2021, 41(s2): 467-471.

焊后热处理对聚变堆用奥氏体不锈钢MAG焊焊缝金属冲击韧性的影响

Effect of post-weld heat treatment on impact toughness of MAG weld metal of austenitic stainless steel for fusion reactor

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics