弹丸消融速率的理论模型及数值计算

doi:10.16568/j.0254-6086.201601002

核聚变与等离子体物理 ›› 2016, Vol. 36 ›› Issue (1): 8-12.DOI: 10.16568/j.0254-6086.201601002

弹丸消融速率的理论模型及数值计算

程发银

(重庆工商大学应用物理系，重庆 400067)

收稿日期:2014-12-31 修回日期:2015-09-09 出版日期:2016-03-15 发布日期:2016-03-15
作者简介:程发银(1968-)，男，四川通江人，博士，副教授，主要从事高温等离子体物理研究。
基金资助:
重庆市教委科技项目(KJ090731)

Theoretical model and numerical calculation of pellet ablation rate

CHENG Fa-yin

(1. Southwestern Institute of Physics, Chengdu 610041; 2. Institute of Plasma Physics, Chinese Academy of Science, Hefei 230031)

Received:2014-12-31 Revised:2015-09-09 Online:2016-03-15 Published:2016-03-15

摘要/Abstract

摘要：

建立了计算托卡马克加料中弹丸消融的物理模型，结合1维输运模型编制了1.5维弹丸消融计算机模拟代码。使用ITER-FEAT的相关参数，对半径为6mm，初速度为2000m•s^-1，从低磁场侧注入弹丸的消融速率进行了模拟计算。结果显示，弹丸消融速率先随注入深度而逐渐增大，最大消融速率约6×10²⁶s^-1，然后由于弹丸半径的减小，消融速率迅速减小，穿透深度约0.45m。这一结果与中性气体屏蔽模型(NGS)的结果一致，证明计算代码正确有效。同时，从计算结果反映出，对ITER这样的堆级托卡马克，采用常规弹丸注入方式，尽管速度高达2000m•s^-1，穿透深度也远未达到等离子体中心，因此应采取其他有效措施来提高等离子体加料效率。

关键词: 弹丸, 加料, 消融速率, 穿透深度

Abstract:

A physical model of calculating the pellet ablation rate in tokamak fueling was proposed, which was combined with the 1-D transport model to develop the 1.5D pellet ablation code. Using the parameter of ITER-FEAT, the pellet ablation rate of radius 6mm with initial injection speed of 2000m•s^-1 when injecting from low field side was calculated. The results show that the ablation rate first increases gradually over time, then decreases rapidly because of decrement of pellet radius, the maximum ablation rate is about 6×10²⁶s^-1, the total penetration depth is about 0.45m. This result is consistent with that gained from the neutral gas shielding model (NGS), and it proved the validity of the code. At the same time, the calculation result indicate that, for the reactor grade tokamak such as ITER, using conventional pellet injection method, the penetration depth is small enough so that the core plasma fueling cannot be achieved although the injection speed is 2000m•s^-1. Therefore in order to raise the plasma fueling efficiency, other effective pellet injection scenario must be chosen.

Key words: Pellet, fueling, Ablation rate, Penetration depth

中图分类号:

O532+.11

程发银. 弹丸消融速率的理论模型及数值计算[J]. 核聚变与等离子体物理, 2016, 36(1): 8-12.

CHENG Fa-yin. Theoretical model and numerical calculation of pellet ablation rate[J]. NUCLEAR FUSION AND PLASMA PHYSICS, 2016, 36(1): 8-12.

参考文献

[1] Lang P T, Gafert J, Gruber O, et al. High density operation in H mode discharges by inboard launch pellet refueling[J]. Nucl. Fusion, 2000, 40: 245-260.
[2] Lang P T, Buchl K, Kaufmann N, et a1. High-efficien Plasma refuelling by pellet injection from the magnetic high-field side into ASDEX-upgrate[J]. Phys. Rev. Lett., 1997, 79: 1487-1495.
[3] Baylor L R, Jemigan T C, Houlberg A, et a1. Improved core fueling with high field side pellet injection in the DIII-D tokamak[J]. Phys. Plasma, 2000, 7: 1878-1885.
[4] Parks P B, Baylor L R. Effect of parallel flows and toroidicity on cross-field transport of pellet ablation matter in tokamak plasmas[J]. Phys. Rev. Lett., 2005, 94: 125002.
[5] Baylor L R, Combs S K, Jernigan T C, et al. Pellet fueling technology development leading to efficient fueling of ITER burning plasmas[J]. Phys. Plasmas. 2005, 12: 056103.
[6] Parks P B, Rosenbluth M N. Equilibrium pellet and liquid jet shape under high ablation pressures[J]. Phys. Plsamas, 1998, 5: 1380-1386.
[7] Rosenbluth M N, Putvinskij S V, Parks P B. Liquid jets for fast plasma termination in tokamaks[J]. Nucl. Fusion, 1997, 37: 955-966.
[8] Pegourie B, Picchiottino J M, Drawn H W, et al. Pellet ablation studies on tore supra[J]. Nucl. Fusion, 1993, 33: 591-600.
[9] Parks P B，Tumbull R J，Foster C A，et al．A model for the ablation rate of a solid hydrogen pellet in a plasma[J]. Nucl. Fusion, 1977, 17: 539-556．
[10] Kuteev B V. Hydrogen pellet ablation and acceleration by current in high temperature plasma[J]. Nucl. Fusion, 1995, 35: 431-453.
[11] 程发银, 兰明建. 等离子体中氖输运及辐射特性模拟[J]. 原子与分子物理学报, 2008, 25: 446-450.
[12] Cheng F Y, Shi B R. Study of impurity behavior in non-coronal equilibrium state[J]. Chinese Phys., 2007, 16: 3458-3463.
[13] Wisitsorasak A, Onjun O. Impacts of pellets injected from the low-field side on plasma in ITER[J]. Plasma Physics Reports, 2011, 37: 1-18.
[14] Fehlberg E. Classical fifth-, sixth-, seventh-，and eighth order Runge-Kutta formulas with stepsize control[R]. NASA Technical Report, 1968. 87.
[15] Campbell D J. The physics of the international thermonuclear experimental reactor FEAT[J]. Phys. Plasmas, 2001, 8: 2041-2046.
[16] Shimonura Y, Aymar R, Chuyanov V, et al. The ITER design[R]. IAEA-CN-77/ITER/1, 2000.
[17] Aymar R, Chuyanov V, Huguet M, et al. The ITER design[R]. Proceeding of the 18th International Fusion Energy Conference, Sorrento Italy, Paper No. IAEA-CN -77/ ITEROV/1, 2000.
[18] Ishizaki R, Parks P B, Nakajima N, et al. Two- dimensional simulation of pellet ablation with atomic processes[J]. Phys. Plasmas, 2004, 11: 4064-4080.

弹丸消融速率的理论模型及数值计算

Theoretical model and numerical calculation of pellet ablation rate

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

[1]	李运海, 叶扬∗, 唐良浩, 谭名昇, 童义, 杨荣, 谢晓峰, 邓天白, 孔德峰, 陶骏 . 紧凑环芯部加料装置用大电流高重频脉冲电源系统的研制[J]. 核工业西南物理研究院, 2024, 44(3): 304-311.
[2]	李孟曼妮, 侯吉磊, 左桂忠, 陈跃, 李成龙, 刘建文, 叶凯萱, 黄佳, 胡建生 . EAST中加热功率对弹丸注入加料效率的影响 [J]. 核聚变与等离子体物理, 2022, 42(4): 426-432.
[3]	鲁鑫, 吴雪科, 胡世林, 严一帆, 李正吉, 王占辉. HL-2A 充气弹丸注入加料的数值模拟研究[J]. 核聚变与等离子体物理, 2021, 41(3): 199-206.
[4]	徐红兵1，曹曾1，陈程远1，朱根良1，蔡潇1，刘亮1，李永高1，杨曾辰1，钟云柯1，张占文2，刘德权1. HL-2A充气弹丸注入初步实验结果[J]. 核聚变与等离子体物理, 2020, 40(2): 104-108.
[5]	袁啸林1, 2，陈跃1, 李建刚1，胡建生1，周跃1，侯吉磊1, 2，黄明1. 基于实验物理与工业控制系统的EAST 真空抽气及加料控制系统设计[J]. 核聚变与等离子体物理, 2019, 39(1): 34-40.
[6]	陈程远，姚良骅，冯北滨，周艳，严龙文. HL-2A装置超声分子束注入加料效率的研究[J]. 核聚变与等离子体物理, 2010, 30(1): 1-6.
[7]	牛兴平1，吴斌2. EAST等离子体破裂的数值模拟[J]. 核聚变与等离子体物理, 2007, 27(4): 286-291.
[8]	洪文玉，严龙文，钱俊，赵开君，程均，罗萃文，徐征宇，冯北滨. HL-2A装置边缘扰动特性观测[J]. 核聚变与等离子体物理, 2007, 27(4): 306-310.
[9]	徐红兵，刘德权，肖正贵，朱根良，王明建. HL-2A装置中基于循环制冷机的弹丸发射器方案设计[J]. 核聚变与等离子体物理, 2007, 27(2): 131-136.
[10]	洪文玉，严龙文，钱俊，潘宇东，罗萃文，徐征宇，潘莉，杨青巍，黄渊. HL-2A偏滤器位形的边缘等离子体特性[J]. 核聚变与等离子体物理, 2006, 26(2): 81-86.
[11]	彭利林, 邓柏权, 袁涛, 严建成. 改善ITER 弹丸注入芯部加料的研究[J]. 核聚变与等离子体物理, 2005, 25(3): 189-194.